Read Or Download Powerflex 4 Manual Fault Codes For FREE at THEDOGSTATIONCHICHESTER.CO.UK. The cause of the fault will have to be corrected before the fault can be reset and the drive started. The following is a listing of the possible fault codes of the Allen Bradley PowerFlex 40 drive and short descriptions of the causes. Fault 4 - UnderVoltage - DC bus voltage fell below the minimum value of 407V DC at 400/480V input or 204V DC at 200/240V input. Fault 101 - UserSet1 Chksum - The checksum read from the user set does not match the checksum calculated. Fault 102 - UserSet2 Chksum - The checksum read from the user set does not match the checksum calculated. Drive as; drive, PowerFlex 400 or PowerFlex 400 Drive. Parameter numbers and names are shown in this format:. The following words are used throughout the manual to describe an action: Drive Frame Sizes Similar PowerFlex 400 drive sizes are grouped into frame sizes to simplify spare parts ordering, dimensioning, etc.
Commons Issues with Allen-Bradley PowerFlex Drives
Troubleshooting a faulted drive can be a tough endeavour. We're here to help! The list below features some of the most common reasons why Allen-Bradley PowerFlex drives can fault and how to solve those issues. If you've tried all of the tips below and there's still an problem with your drive, it might be time to contact your service provider for a repair or replacement. Contact us today for support!
Problems and Solutions for Allen-Bradley PowerFlex Drives
Read Or Download Powerflex 4 Manual Fault Codes For FREE at THEDOGSTATIONCHICHESTER.CO.UK. The cause of the fault will have to be corrected before the fault can be reset and the drive started. The following is a listing of the possible fault codes of the Allen Bradley PowerFlex 40 drive and short descriptions of the causes. Fault 4 - UnderVoltage - DC bus voltage fell below the minimum value of 407V DC at 400/480V input or 204V DC at 200/240V input. Fault 101 - UserSet1 Chksum - The checksum read from the user set does not match the checksum calculated. Fault 102 - UserSet2 Chksum - The checksum read from the user set does not match the checksum calculated. Drive as; drive, PowerFlex 400 or PowerFlex 400 Drive. Parameter numbers and names are shown in this format:. The following words are used throughout the manual to describe an action: Drive Frame Sizes Similar PowerFlex 400 drive sizes are grouped into frame sizes to simplify spare parts ordering, dimensioning, etc.
Commons Issues with Allen-Bradley PowerFlex Drives
Troubleshooting a faulted drive can be a tough endeavour. We're here to help! The list below features some of the most common reasons why Allen-Bradley PowerFlex drives can fault and how to solve those issues. If you've tried all of the tips below and there's still an problem with your drive, it might be time to contact your service provider for a repair or replacement. Contact us today for support!
Problems and Solutions for Allen-Bradley PowerFlex Drives
- Contamination/Corrosion
- Disconnect power and remove contamination (metal shavings, dust) with compressed dry air. The Allen-Bradley Powerflex drive should be sent in for service if it's soaked with oil or other liquid contaminants.
- Loose connections
- Electronics are limited to their wiring. Vibrations, physical manipulation or relocation may loosen terminal connections. Verify and secure all terminal connections.
- Missing power phase
- Check input voltage and verify power is on all phases.
- Bad cables
- Over time and after constant use, cables will wear out from physical damage and contamination. If you have haven't swapped out your cables in a while, secure a new cable and try again.
- Seized cooling fans
- Overheating is the biggest enemy to electronic circuitry. Proper ventialtion requires that fans have been cleaned and devoid of any debris.
- Wrong parameters
- This issue can occur when system memory leaks due to voltage transients and the values change. Backup the parameters using the HIM and reset the drive to factory default, then restore the correct parameters.
- Binded load
- This will usually cause an overcurrent fault. Check gear, fans, pulleys or worm gears for proper operation.
Allen-Bradley PowerFlex Drives
Alarm Numbers and Descriptions
Allen Bradley Powerflex Fault Codes
- 2 Auxiliary Input
- 3 Power Loss
- 4 Under Voltage
- 5 Over Voltage
- 7 Motor Overload
- 8 Heatsink Over Temp
- 9 Transister Over Temp
- 12 HW Over Current
- 15 Load Loss
- 16 Motor Thermistor
- 17 Input Phase Loss
- 24 Decel Inhibit
- 25 Over Speed Limit
- 29 Analog In Loss
- 33 Auto Restart Tries
- 36 SW Over Current
- 38 Phase U to Ground
- 39 Phase V to Ground
- 40 Phase W to Ground
- 41 Phase UV Short
- 42 Phase UW Short
- 43 Phase VU Short
- 48 Params Defaulted
- 49 Drive Powerup
- 51 Fault Queue Cleared
- 52 Faults Cleared
- 63 Shear Pin
- 64 Drive Overload
- 71-75 Port 1-5 Adapter
- 77 IR Volts Range
- 78 Flux Amps Reference Range
- 79 Excessive Load
- 80 AutoTune Aborted
- 81-85 Port 1-5 DPI Loss
- 87 IXo Voltage Range
- 91 Encoder Loss
- 100 Parameter Checksum
- 101 User Set 1 Checksum
- 102 User Set 2 Checksum
- 103 User Set 3 Checksum
- 104 Power Board Checksum 1
- 105 Power Board Checksum 2
- 106 Incompatible MCB-PB
- 107 Replaced MCB-PB
- 108 Analog Calibration Checksum
- 111 Enable Hardware
